Page 7 of 8
Re: How to perform Powershift 6DCT250 (DPS6) adaptive learning
Posted: Fri Mar 31, 2023 2:56 am
by rich935
Chevygibbs wrote: Thu Mar 30, 2023 11:23 pm
I’m not sure where else to ask but I’m trying to do a tcm adaptive learning for a 2012 ford focus with the dps6 transmission.the software seems to just hang up and not do anything past about half way. It goes to 100% then restarts at 50% and climbs again over and over. It gets all the way to shift drum adaptive leaning and says ok but when it gets to gear command for neutral state for both transmission shafts it just doesn’t seem to go any further any help would be appreciated thanks
I've had this happen before a few times. Have you tried resetting all the modules beforehand? Is it in FTDI mode? Also what seemed to work once is driving it in limp mode for about two miles first. But mostly resetting the BCM and if that doesn't work reset all of them first. Oh yeah also make sure the car is up to temperature first or in the middle of the gauge then try the adaptive learning. I don't know what else you can try. Good luck.
Re: How to perform Powershift 6DCT250 (DPS6) adaptive learning
Posted: Mon Apr 03, 2023 10:35 pm
by Chevygibbs
I have tried resetting all models especially the body control module.I have ftdi mode set to auto is that ok? It’s just so strange when it gets to select gears for neutral state it just hangs up and can’t get past it. do you know what’s it’s testing or what it’s doing when it’s tests that particular part? I can’t figure it out and car is stuck where it’s at. I would hate to have to take it to dealer
Re: How to perform Powershift 6DCT250 (DPS6) adaptive learning
Posted: Mon Apr 03, 2023 10:45 pm
by rich935
Have you let the car warm up first? Can you try driving the car in limp mode for a mile or two? I don't know what else to try. This has happened to me before a few times. And that's what worked warm up and driving like two miles in limp mode then trying it.
Re: How to perform Powershift 6DCT250 (DPS6) adaptive learning
Posted: Mon Apr 03, 2023 11:24 pm
by Chevygibbs
I can’t really drive it cause my drive way is at bottom of steep hill and it doesn’t have enough runway before it just quits like it’s in neutral I guess that’s the limp mode your referring to. I might try jacking car up to spin wheels freely that way what are your thoughts?
Re: How to perform Powershift 6DCT250 (DPS6) adaptive learning
Posted: Mon Apr 03, 2023 11:25 pm
by Chevygibbs
I also have warmed car up with temp gauge half way but why would that matter anyway just curious?
Re: How to perform Powershift 6DCT250 (DPS6) adaptive learning
Posted: Tue Apr 04, 2023 1:51 am
by jhonma07
I changed the module but the module that I have failed did not work if it allows me to carry out the 5 steps but when I connect the new module in step 3, which is the drum, it shows me that the process has been interrupted, I am using the "Vgate vLinker" cable FS", the faulty module is AE8Z-7Z369-F and the new module is AE8P-14F085-AE, I don't know if I should do something before starting TCM adaptive learning
Re: How to perform Powershift 6DCT250 (DPS6) adaptive learning
Posted: Fri Apr 07, 2023 11:00 am
by support_team
jhonma07 wrote: Tue Apr 04, 2023 1:51 am
[...] when I connect the new module in step 3, which is the drum, it shows me that the process has been interrupted, [...]
Please address your problem to the
support team and provide debug information.
Re: How to perform Powershift 6DCT250 (DPS6) adaptive learning
Posted: Fri Apr 07, 2023 11:25 pm
by DriverRider
jhonma07 wrote: Tue Apr 04, 2023 1:51 am
I changed the module but the module that I have failed did not work if it allows me to carry out the 5 steps but when I connect the new module in step 3, which is the drum, it shows me that the process has been interrupted, I am using the "Vgate vLinker" cable FS", the faulty module is AE8Z-7Z369-F and the new module is AE8P-14F085-AE, I don't know if I should do something before starting TCM adaptive learning
The newest revised TCM is the AE8Z-F for the 2012-2014 and has been on back-order for almost two years according to my Dealer. You are using an old and likely used Module which I think would need initial program/flashing to your vehicle or might be one of the many defective ones.
Re: How to perform Powershift 6DCT250 (DPS6) adaptive learning
Posted: Sat Apr 08, 2023 1:48 am
by jhonma07
One question, is there a problem with the HW of the old TCM being AE8Z-7Z369-F, and the new one being HW AE8P-14F085-AE, if so, it is the reason that it does not allow me to learn
Re: How to perform Powershift 6DCT250 (DPS6) adaptive learning
Posted: Sat Apr 20, 2024 3:32 pm
by mustangy
Green Flag reset error,
TCM software update to latest april 2024
Voltage is 12.9 both battery and obd
cables claened all good
this found at service manual.
Still stuck at reset green cluctch flag error
obdmax+ obdlink EX same results
Car is heated to 90 degree
all seems good but this error keep pops ?
LUK brand clutch forks actuators bearing and clutch all replaced 2014 Focus
car run and drive i just want make sure relearn pattern kicks in.
