zivnic wrote: Fri Jul 08, 2022 6:40 am
Hi, I have Mondeo MK5 facelift Ecoblue 110kw. When I tried to change to more power in Forscan, it did say error and didn´t change anything. Is it possible in those new facelift motors to chenge to 180km or is it forbidden? Thank you very much.
If you have 110kw ecoblue, you also have adblue. The most powerful engine it had (at least in S-Max and Galaxy) was 140 kw, that is 190 horsepower. And 110kw is 150 horsepower.
Forscan only offers 180 horsepower and that's 132 kw. Which does not match your engine.
I was dealing with something similar on my S-Max 2019 2.0 Ecoblue 110kw - 150hp engine.
zivnic wrote: Wed Jul 13, 2022 10:39 am
Thank you very much for your post. So it is not possible to change it in higher power at this moment?
Not now.
I work in the Ford warranty department for the Czech Republic.
I have addressed this issue with both the technical engineer for Ford and the chief diagnostician.
He said that he personally wouldn't change it, since Forscan doesn't even know what kind of engine we actually have and it only offers me old engines - without adblue.
by the way, it just occurred to me that Forscan even shows me that I have 180 hp, while according to the nameplate I have 110 kw - i.e. 150 hp...
Ok, thank you very much! Maybe can I ask you another issue? On my facelift, I have traffic signs just when camera reads it. But in older Myk5 that we have - 2016 - it shows all the time on IPC as it get it from APIM. I tried to change it in IPMA for reading Camera+APIM (originaly set just for Camera and in 2016 MK5 we have it set for Camera+APIM). But when I change it in IPMA, write it, it says ok. But when I het back to IPMA programming, thare is again just Camera. Do you have any clue how to make it work? Btw, I am from the Czech republic
zivnic wrote: Thu Jul 14, 2022 5:29 am
Ok, thank you very much! Maybe can I ask you another issue? On my facelift, I have traffic signs just when camera reads it. But in older Myk5 that we have - 2016 - it shows all the time on IPC as it get it from APIM. I tried to change it in IPMA for reading Camera+APIM (originaly set just for Camera and in 2016 MK5 we have it set for Camera+APIM). But when I change it in IPMA, write it, it says ok. But when I het back to IPMA programming, thare is again just Camera. Do you have any clue how to make it work? Btw, I am from the Czech republic
Previous car, does it have navigation? If so, then IPC takes data from the navigation, because the navigation is more where the village ends and begins...
So:
with navigation takes data from it and reads
without navigation it only reads
You can easily change the 150HP Ecoblue in the Mondeo to 190HP, but it only works with the automatic version.
The labeling in Forscan is just wrong and says 180HP, but it is indeed the 190HP Version.
Just switch from Panther to Panther B in the PCM.
To do it like factory, you also have to change a Bit in the ABS, it's the same, as with the old TDCI.
Also the ABS Bit doesn't make any obvious difference.
I used the 190HP Config for a few days and there was an instant increase in top speed and acceleration.
peter1975sol wrote: Wed Jul 27, 2022 6:45 pm
You can easily change the 150HP Ecoblue in the Mondeo to 190HP, but it only works with the automatic version.
The labeling in Forscan is just wrong and says 180HP, but it is indeed the 190HP Version.
Just switch from Panther to Panther B in the PCM.
To do it like factory, you also have to change a Bit in the ABS, it's the same, as with the old TDCI.
Also the ABS Bit doesn't make any obvious difference.
I used the 190HP Config for a few days and there was an instant increase in top speed and acceleration.
I personally did not go into it, because Forscan tells me that I have 180HP. But in reality I only have 150HP.
For this reason alone, I preferred not to do anything with it...
There are a few things in the newer cars, where the forscan labels aren't correct or missing.
So when you really want to be sure, you have to look in the asbuilts and compare a 150hp to a 190hp.
Hi,does anyone tried this mod on mondeo mkv 2015? i have done it on my car and i see no difference in power.
I monitored before and after boost pressure and it is the same(max boost 270% or 270kpa map sensor),i have pcm firmware version HS7A-14C204-CFE.
I even downgraded to early version of firmware FS7A-14C204-DXC and no difference.
The only change i see is the engine output torque from 114% max (150ps) to 124% max (180ps mod).
If this is working for someone please share your max boost pressure,thanks.
Good morning.
sorry for my English but it's the google translate.
I have a smax of 2016 150cv tdci. with these changes it really goes to 180hp?
I am not very put with forscan but if I have located the steps to follow, lower consumption?
