Page 1 of 1
PDM,ddm module ubdated
Posted: Mon May 06, 2019 1:01 pm
by marekrbk
Mondeo mk4 1.8tdci 2007 92kw
Forscan 2.4.0 test20190403
![Image]()
![Image]()
why this? after update code: u0300
is a solution? 
Re: PDM,ddm module ubdated
Posted: Sun Nov 10, 2019 3:29 pm
by nurex
I have the same problem.
Is there a solution???
- IMG_20191110_132710.jpg (159.57 KiB) Viewed 9447 times
- IMG_20191110_132201.jpg (165.98 KiB) Viewed 9447 times
- IMG_20191109_115138.jpg (262.6 KiB) Viewed 9447 times
Re: PDM,ddm module ubdated
Posted: Fri Nov 15, 2019 4:29 am
by Ptrck600
marekrbk wrote: Mon May 06, 2019 1:01 pm
Mondeo mk4 1.8tdci 2007 92kw
Forscan 2.4.0 test20190403
![Image]()
![Image]()
why this? after update code: u0300
is a solution?
Try what the troubleshooting says.
Run CCMii sensor alignment service function
Re: PDM,ddm module ubdated
Posted: Fri Nov 15, 2019 3:56 pm
by marekrbk
such a feature is not supported forscan
Re: PDM,ddm module ubdated
Posted: Tue Mar 03, 2020 6:18 pm
by marekrbk
I updated the modules with original calibrations. all without mistakes. using ucds cable
Re: PDM,ddm module ubdated
Posted: Thu Mar 05, 2020 6:01 pm
by marekrbk
return the original calibration,error u0300 removed.
folding rearview mirrors the function expires. if you want the function again, update only DDM
Re: PDM,ddm module ubdated
Posted: Wed Sep 29, 2021 6:24 pm
by danczx7841
marekrbk wrote: Thu Mar 05, 2020 6:01 pm
return the original calibration,error u0300 removed.
folding rearview mirrors the function expires. if you want the function again, update only DDM
Hi have you got the files to download
Re: PDM,ddm module ubdated
Posted: Wed Sep 29, 2021 6:25 pm
by danczx7841
marekrbk wrote: Thu Mar 05, 2020 6:01 pm
return the original calibration,error u0300 removed.
folding rearview mirrors the function expires. if you want the function again, update only DDM
Hi have you got the files to download
Re: PDM,ddm module ubdated
Posted: Wed Nov 10, 2021 4:18 am
by mtech
I had some DTCs after flashing new firmware to PDM. The PDM was inop after flash, no normal functions.
The flash was successful, but was getting a few DTCs on the PDM, including 'Missing Calibration'. The PDM was not responding correctly, as I could not activate the power fold mirrors on the passenger side.
What I found is that the As Built configuration went to some default state after the firmware flash. I restored from a backup I made earlier and then the PDM started to work normally with the new firmware. DTCs went away.
Re: PDM,ddm module ubdated
Posted: Sun Dec 19, 2021 1:30 pm
by nurex
I have the solution for U0300.
If you update DDM and PDM to software with the last letter E or F, then the rear modules must have the same last letter. After that, the U0300 DTC is gone
- Screenshot_2021-12-19-15-19-41-54_c0dc27f5c07cb0fb3541d6073dfd6932.jpg (455.35 KiB) Viewed 5545 times