Forscan 2.4.0 test20190403
why this? after update code: u0300
is a solution?
PDM,ddm module ubdated
-
marekrbk
- Posts: 23
- Joined: Wed Nov 22, 2017 7:35 pm
- Vehicle: Ford Mondeo mk5 110kw ,2020
- Location: Slovakia
PDM,ddm module ubdated
Mondeo mk4 1.8tdci 2007 92kw
Forscan 2.4.0 test20190403
![Image]()
![Image]()
why this? after update code: u0300
is a solution?
Forscan 2.4.0 test20190403
why this? after update code: u0300
is a solution?
- Attachments
-
- IMG_20190506_111530.jpg (283.91 KiB) Viewed 10032 times
-
- IMG_20190506_105429.jpg (301.02 KiB) Viewed 10032 times
Re: PDM,ddm module ubdated
I have the same problem.
Is there a solution???
Is there a solution???
- IMG_20191110_132710.jpg (159.57 KiB) Viewed 9434 times
- IMG_20191110_132201.jpg (165.98 KiB) Viewed 9434 times
- IMG_20191109_115138.jpg (262.6 KiB) Viewed 9434 times
Re: PDM,ddm module ubdated
Try what the troubleshooting says.marekrbk wrote: Mon May 06, 2019 1:01 pm Mondeo mk4 1.8tdci 2007 92kw
Forscan 2.4.0 test20190403
why this? after update code: u0300
is a solution?
Run CCMii sensor alignment service function
-
marekrbk
- Posts: 23
- Joined: Wed Nov 22, 2017 7:35 pm
- Vehicle: Ford Mondeo mk5 110kw ,2020
- Location: Slovakia
Re: PDM,ddm module ubdated
such a feature is not supported forscan
-
marekrbk
- Posts: 23
- Joined: Wed Nov 22, 2017 7:35 pm
- Vehicle: Ford Mondeo mk5 110kw ,2020
- Location: Slovakia
Re: PDM,ddm module ubdated
I updated the modules with original calibrations. all without mistakes. using ucds cable
- Attachments
-
- Snímka obrazovky (9).jpg (22.62 KiB) Viewed 8624 times
-
- 89098707_635363810581374_554997546594861056_n.jpg (66.53 KiB) Viewed 8639 times
-
marekrbk
- Posts: 23
- Joined: Wed Nov 22, 2017 7:35 pm
- Vehicle: Ford Mondeo mk5 110kw ,2020
- Location: Slovakia
Re: PDM,ddm module ubdated
return the original calibration,error u0300 removed.
folding rearview mirrors the function expires. if you want the function again, update only DDM
folding rearview mirrors the function expires. if you want the function again, update only DDM
-
danczx7841
- Posts: 2
- Joined: Sun Nov 29, 2020 2:45 pm
- Vehicle: mondeo mk3 125 bhp 2009
Re: PDM,ddm module ubdated
Hi have you got the files to downloadmarekrbk wrote: Thu Mar 05, 2020 6:01 pm return the original calibration,error u0300 removed.
folding rearview mirrors the function expires. if you want the function again, update only DDM
-
danczx7841
- Posts: 2
- Joined: Sun Nov 29, 2020 2:45 pm
- Vehicle: mondeo mk3 125 bhp 2009
Re: PDM,ddm module ubdated
Hi have you got the files to downloadmarekrbk wrote: Thu Mar 05, 2020 6:01 pm return the original calibration,error u0300 removed.
folding rearview mirrors the function expires. if you want the function again, update only DDM
Re: PDM,ddm module ubdated
I had some DTCs after flashing new firmware to PDM. The PDM was inop after flash, no normal functions.
The flash was successful, but was getting a few DTCs on the PDM, including 'Missing Calibration'. The PDM was not responding correctly, as I could not activate the power fold mirrors on the passenger side.
What I found is that the As Built configuration went to some default state after the firmware flash. I restored from a backup I made earlier and then the PDM started to work normally with the new firmware. DTCs went away.
The flash was successful, but was getting a few DTCs on the PDM, including 'Missing Calibration'. The PDM was not responding correctly, as I could not activate the power fold mirrors on the passenger side.
What I found is that the As Built configuration went to some default state after the firmware flash. I restored from a backup I made earlier and then the PDM started to work normally with the new firmware. DTCs went away.
Re: PDM,ddm module ubdated
I have the solution for U0300.
If you update DDM and PDM to software with the last letter E or F, then the rear modules must have the same last letter. After that, the U0300 DTC is gone
If you update DDM and PDM to software with the last letter E or F, then the rear modules must have the same last letter. After that, the U0300 DTC is gone
- Screenshot_2021-12-19-15-19-41-54_c0dc27f5c07cb0fb3541d6073dfd6932.jpg (455.35 KiB) Viewed 5532 times