Page 25 of 29

Re: REMOTE START

Posted: Sat Mar 02, 2024 11:11 am
by Crusader
hi everyone,

i have fiesta mk8 1.0 auto keyless entry

i did

BCM module- configuration parameters
• Remote start - enable
Hood Switch enable

IPC module - configuration parameters
Hood switch enable
• Remote start - enable
• Remote start - climate settings- enable

i have all 3 keys working but my problem is HOOD AJAR LIGHT WARNING . i dont have hood ajar sensor

remote start one beep problem

https://www.youtube.com/watch?v=scds5mI ... el=WoneOne

i have same problem any idea how can i fix hood ajar light warning

Image

Re: REMOTE START

Posted: Sat Mar 02, 2024 12:38 pm
by Ghano38
You need to replace the hood lock.one wire goes to BCM(don’t know witch one for the Fiesta) the second one goes to the car body other the circuit is open that’s why you have the hood ajar on.

Re: REMOTE START

Posted: Wed Mar 06, 2024 8:31 pm
by Blueprintsud
Crusader wrote: Sat Mar 02, 2024 11:11 am hi everyone,

i have fiesta mk8 1.0 auto keyless entry

i did

BCM module- configuration parameters
• Remote start - enable
Hood Switch enable

IPC module - configuration parameters
Hood switch enable
• Remote start - enable
• Remote start - climate settings- enable

i have all 3 keys working but my problem is HOOD AJAR LIGHT WARNING . i dont have hood ajar sensor

remote start one beep problem

https://www.youtube.com/watch?v=scds5mI ... el=WoneOne

i have same problem any idea how can i fix hood ajar light warning

Image
did you do this step ?

RTM module AsBuilt value: 751-01-01 x2xx xxxx.

Re: REMOTE START

Posted: Wed Mar 06, 2024 10:06 pm
by yanir99
fordsmax471 wrote: Tue Dec 17, 2019 6:19 pm Hi !

Remote start the car ( Ford S-Max 2.0 TDCi 2017 PowerShift )

4Button Remote smart Key 433 or 434 MHZ DS7T-15K601-EF (please see ford etis )

guide for Ford S-Max mk2
To activate Remote Start, first you need a new key fob with start button (part # DS7T-15K601-EF for S-Max mk2 with 434 MHz).

:!: Note ! remove the metal blanks from the keys, the car doors are closed and the handbrake deactivated.

Programming keys
Determine the backup slot of the passive key.

:arrow: Place the first programmed key in the backup slot. Press the START / STOP button.
Wait for 4-5 seconds, then press the START / STOP button.
Extract the first programmed passive key.

:arrow: Within 5 seconds, place the second programmed passive key in the backup slot, then press the START / STOP button.
Wait for 4-5 seconds, then press the STOP-STOP button.
Extract the second programmed key.

:arrow: Within 5 seconds, place the unprogrammed passive key in the backup slot and press the START / STOP button.

Car doors lock and opened, lights blink
Congratulations on your new key being programmed !!! :)

Now use Forscan to change the asbuilt-data

BCM module- configuration parameters
• Remote start - enable

IPC module - configuration parameters
• Remote start - enable
• Remote start - climate settings- enable
• Remote start - front seat- enable (optional)
• Remote start - rear defrost – enable (optional)
• Remote start - steering feel – enable (optional)

some guides recommend
RTM module - configuration parameters
don't change anything :!: ( old keys can also be used in the future )
New here, and after reading through I can say the following:

for my 2019 S-MAX the above procedure didn't work - BUT I managed to get this working ;)
After ordering a new key with remote start button, I had to do the following:
  • Using Forscan with full 1-year license and the recommended cable.
  • Under the service menu (wrench icon) found the setting that has PATS in the description
  • Activated this procedure, got a warning that it must be with supported cable and full license -> confirmed
  • There were a couple of options there, one was to enable the programing procedure (which I believe what enables the procedure described in the 1st post here) -> I enabled it.
  • placed my new key with the remote start button on the programming tray.
  • There is an option to program a new key -> ran this, it confirmed that the new key is programmed.
  • Exited this PATS settings.
  • In the modules menu in IPC and BCM enabled the options as described above (didn't change any RTM)
  • exited everything, tuned off the car, got out, locked the car.
  • on the new remote press once on "lock" and then twice on the "remote start" button -> the car starts :D
All keys (old and new) are working (button, proximity and ignition) without the need to be in the programming tray.

Hope this helps.

Re: REMOTE START

Posted: Thu Mar 07, 2024 9:24 pm
by keepchooglin
Thanks for your reply! I'm gonna try these steps! Hope that's the solution to getting all the keys working.

Re: REMOTE START

Posted: Fri Mar 08, 2024 9:17 am
by Crusader
Blueprintsud wrote: Wed Mar 06, 2024 8:31 pm
Crusader wrote: Sat Mar 02, 2024 11:11 am hi everyone,

i have fiesta mk8 1.0 auto keyless entry

i did

BCM module- configuration parameters
• Remote start - enable
Hood Switch enable

IPC module - configuration parameters
Hood switch enable
• Remote start - enable
• Remote start - climate settings- enable

i have all 3 keys working but my problem is HOOD AJAR LIGHT WARNING . i dont have hood ajar sensor

remote start one beep problem

https://www.youtube.com/watch?v=scds5mI ... el=WoneOne

i have same problem any idea how can i fix hood ajar light warning

Image
did you do this step ?

RTM module AsBuilt value: 751-01-01 x2xx xxxx.
For what?

Re: REMOTE START

Posted: Tue Mar 26, 2024 10:05 am
by Crusader
I did bypass for hood switch. Now working on Fiesta mk8

Re: REMOTE START

Posted: Wed Apr 10, 2024 3:30 pm
by Blueprintsud
keepchooglin wrote: Thu Mar 07, 2024 9:24 pm Thanks for your reply! I'm gonna try these steps! Hope that's the solution to getting all the keys working.
did you get it to work ?

I have 3 options here

ignition key programmering
erase and program keys
spare keys programmable


wich option is valid ?

Re: REMOTE START

Posted: Wed Apr 10, 2024 3:45 pm
by Blueprintsud
Iam getting Pats Fails I guess is my Key

Re: REMOTE START

Posted: Wed Apr 17, 2024 8:13 pm
by yanir99
Blueprintsud wrote: Wed Apr 10, 2024 3:45 pm Iam getting Pats Fails I guess is my Key
Could be, the key must be empty - I ordered this one: https://www.aliexpress.com/item/1005006236115751.html and it worked